EMC Interface Protection for the Shenji NX9031C Intelligent Driving Domain Control Platform
Français
7days a week from 9:00 am to 9:0pm
+86 18001853095

Shanghai Leiditech上海雷卯电子科技有限公司是专业的静电保护元件厂家,TVS二极管供应商;专业提供防雷防静电方案,电磁兼容EMC免费测试等服务,品质保证,库存充足,型号齐全,值得信赖,如有采购静电保护元件,TVS二极管需求,请联系雷卯,24小时服务热线:021-50828806.

By LEIDITECH | 09 October 2026 | 0 commentaires

EMC Interface Protection for the Shenji NX9031C Intelligent Driving Domain Control Platform

 

Figure 1: Shenji NX9031C domain control platform EMC full-interface protection (Shanghai Leiditech)

Introduction: When 5nm automotive-grade intelligent driving chips meet logistics vehicle domain control

The Shenji NX9031C is a dedicated intelligent driving domain control platform launched by Shenji Technology for logistics vehicles and commercial vehicle scenarios. Founded in June 2025, Shenji has completed nearly 3 billion RMB in financing. Its NX9031 series chips are manufactured using 5nm automotive-grade process and have formed a complete product portfolio consisting of multiple chips including NX9031X, NX9031U, and NX9031C, covering three major AI tracks: intelligent assisted driving, embodied intelligence, and Agent reasoning.

At the 2026 World Artificial Intelligence Conference (WAIC), Anhui Shenji Technology Co., Ltd. unveiled an autonomous driving controller for logistics vehicles. Its core is powered by NIO's self-developed 5nm automotive-grade intelligent driving chip NX9031C: featuring over 50 billion transistors, 32-core big.LITTLE CPU, NPU computing power of approximately 1000 TOPS, LPDDR5x 8533Mbps memory bandwidth, 6.5G Pixel/s high-performance ISP, and ASIL-D functional safety certification. As of mid-2026, over 550,000 Shenji NX9031 chips have been mass-produced and deployed in vehicles, supporting dual-chip millisecond-level hot standby.

For EMC engineers, this chip means that 16 RAW cameras, 3D cameras, LiDAR, millimeter-wave radar, high-precision GNSS, automotive Ethernet ring backbone, and CAN FD/LIN body networks all converge on a single domain control board. The combination of high speed, high density, and high reliability means that interface ESD and surge protection is no longer a simple matter of "just put a TVS on it." Instead, it demands systematic design across interface topology, signal integrity, automotive-grade certification, and manufacturability.

Based on 16 years of experience in EMC components and solutions, the Leiditech EMC engineer provides a detailed breakdown of the key interface protection for the NX9031C domain control platform, offering directly implementable automotive-grade component solutions.

I.Why is EMC design for the NX9031C domain controller more difficult?

1. The more advanced the process, the more fragile the I/O. The gate oxide thickness and breakdown voltage of 5nm process are far lower than mature nodes, making transient ESD more likely to cause gate oxide breakdown or latch-up.

2. High-speed interfaces are extremely sensitive to parasitic capacitance. High-speed differential lines such as 100/1000BASE-T1 and SerDes/FPD-Link require ESD device junction capacitance <3pF, otherwise eye diagrams, return loss, and BER will directly degrade.

3. Multiple high-power peripherals coexist. LiDAR, millimeter-wave radar, camera heating, and the domain controller's own edge AI computing mean the 12V/24V power rail must directly face stringent tests such as ISO 7637-2 pulse 5a/5b load dump and ISO 10605-2 Level 4 ESD.

4. ASIL-D functional safety requires redundancy and fail-safe protection. No single point of failure may cause loss of autonomous driving functionality. The clamping voltage, response speed, and short-circuit characteristics of interface protection devices must be incorporated into FMEA in advance.

5. Logistics vehicle scenarios are even harsher. Wide temperature, strong vibration, long cable runs, and complex electromagnetic environments mean protection components must be truly automotive-grade, not industrial-grade "good enough."

二、NX9031C Domain Controller Key Interface Protection Overview 

The table below summarizes the EMC risks and Leiditech recommended components for the common peripheral interfaces on the NX9031C domain control platform. The following sections will expand on the circuit topology and selection considerations for each item.

 

Interfaces

 

Key Risks

Leiditech recommended components

 

Key parameters

In-vehicle Ethernet

ESD, common-mode noise

PESD2ETH100-T
LDW43T-513T

24V bidirectional, 3pF, ±30kV, SOT-23 / common-mode choke

100/1000BASE-T1

ESD, EFT, surge

SMC24LVQ/SMC27LVQ
LDW43T-513T

24V/27V bidirectional, 5pF, ±30kV, SOT-23

CAN FD

ESD

PESD1LIN

15V/24V bidirectional, 15pF, ±23kV, SOD-323

LIN

Load dump, reverse polarity, surge

SM8S24CA/SM8S36CA
S-SK54C + PPTC

ISO 7637-2 5a/5b,
DO-218AB / DO-214AB

12V/24V automotive power supply

ESD, surge, isolation

ESDA05CP
LM-PESD5V0F1BLD-Q
ULC0502P3Q

0.3pF, DFN1006, automotive-grade

BMS daisy chain

ESD, surge

ULC0511CDN
LC05CI

0.35pF / 1pF,
±30kV

III.In-Vehicle Ethernet 100/1000BASE-T1: ESD and Common-Mode Protection for the Data Backbone

The NX9031C supports a high-speed Ethernet ring network, with 100/1000BASE-T1 connections linking the domain controller to LiDAR, cameras, and gateways. These single-pair differential signals are fast and low-amplitude, demanding ESD devices with very low junction capacitance and tight clamping consistency.

For this, Leiditech recommends the PESD2ETH100-T at the connector entry: 24V bidirectional, only 3pF capacitance, ±30kV contact/air ESD, SOT-23 package. Its silicon-based process offers higher reliability and lower temperature drift than polymer alternatives. Pair this with the LDW43T-513T common-mode choke (2800Ω @ 100MHz, 51μH) at the PHY front end to suppress common-mode noise and improve radiated emission margins.

Layout Rules: Place the ESD device as close as possible to the connector, position the common-mode choke near the PHY, and route the differential pair with matched length and spacing. Avoid running other high-speed traces underneath the protection device.

 

 

Figure 2: In-vehicle Ethernet 100/1000BASE-T1 protection solution (PESD2ETH100-T + LDW43T-513T)

IV.CAN FD Bus: Demanding Both Speed and Automotive-Grade Compliance

CAN FD data rates can reach 2Mbps or even 5Mbps, several times faster than traditional CAN. The higher the rate, the more sensitive the bus is to the capacitance of ESD devices; meanwhile, the body network must meet ISO 10605 Level 4 ESD and ISO 7637 pulse 3 transient requirements.

The Leiditech SMC24Q is a mature automotive-grade device, AEC-Q101 qualified, 24V bidirectional, 25pF, ±30kV, suitable for standard CAN nodes. For high-speed CAN FD nodes, the low-capacitance versions SMC24LVQ / SMC27LVQ are recommended: 24V/27V bidirectional, junction capacitance <5pF, ±30kV, with 2-channel integrated SOT-23 package saving space; pair with common-mode choke LDW43T-513T to filter common-mode interference .

 

 

Figure 3: CAN FD Interface ESD and Filtering Protection Solution (SMC24LVQ/SMC27LVQ + LDW43T-513T)

V.LIN Bus: Reliable Protection for Low-Cost Body Applications

 

LIN bus is used for low-speed body control such as doors, seats, lighting, and wipers, with a rate of 20kbps, master-slave architecture with multiple slaves. Although the rate is not high, the large number of nodes, long wiring, and significant ground potential differences make ESD breakdown of transceivers a common occurrence.

Leiditech recommends the PESD1LIN: 24V/15V bidirectional, 15pF, ±23kV, SOD-323 package, single-line-to-ground protection, low cost, and simple PCB layout. For the NX9031C domain controller, although the LIN network is not directly involved in autonomous driving computation, as part of the vehicle's electronic architecture, its EMC stability also impacts functional safety assessment.

 

Figure 4: LIN Bus ESD Protection Solution (PESD1LIN)

VI.12V/24V Automotive Power Supply: Load Dump is a Required Course

Unmanned logistics vehicle platforms typically use a 12V or 24V electrical system. ISO 7637-2 pulse 5a/5b load dump can generate transients of up to 87V/174V on the power lines, lasting hundreds of milliseconds, which can easily cause conventional TVS devices to fail due to over-power conditions.

Leiditech's 12V automotive power solution uses the SM8S24A/SM8S24CA (DO-218AB, 170A, 87V @ 0.5Ω, 200ms) as the primary surge clamp, in series with a PPTC resettable fuse HL30-300 (30V/3A) for overcurrent protection, and a low-loss Schottky diode S-SK54C (40V/5A, VF 0.55V) for reverse polarity protection. For 24V systems, the corresponding parts are SM8S36A/SM8S36CA, 5.0SMDJ36CA, and HL60-300 PPTC.

For 48V mild hybrid platforms, Leiditech also offers complete solutions including SM8S58CA, LM1K58CLV, and LM5D55P10 PMOS reverse protection, which can directly follow the same design approach.

 

Figure 5: 12V Automotive Power Supply Surge Protection Solution (SM8S24CA + HL30-300 + S-SK54C)

VII.BMS Daisy Chain: The Communication Lifeline of High-Voltage Battery Packs

The battery management system (BMS) of new energy logistics vehicles establishes high-speed differential isolated communication between the cell monitoring unit (BMU) and the main control unit (CMU) through a daisy chain. Although the communication transformer provides isolation, it does not eliminate the risk of ESD and surge injection from the connector port.

Leiditech recommends using the ESDA05CP (low snap-back, Ipp 8A, Vc 7.2V) on the IC power supply pins, and the LM-PESD5V0F1BLD-Q (0.3pF, ±30kV, DFN1006 automotive-grade) on the differential signal lines. For dual-channel requirements, the ULC0502P3Q (0.6pF, 2-channel, DFN1006-3) can be used instead. The complete solution meets IEC 61000-4-2 Level 4 and IEC 61000-4-5 6A (8/20μs).

 

Figure 6: Automotive BMS Daisy Chain Communication Protection Solution (ESDA05CP + LM-PESD5V0F1BLD-Q + ULC0502P3Q)

VI.Why do automotive electronics engineers choose Leiditech?

· Automotive-grade certification: Key components such as SMC24, LM-PESD5V0F1BLD-Q, and ULC0502P3Q are qualified for automotive front-end applications, meeting AEC-Q101 and ISO 7637 / ISO 10605 test requirements.

· Full interface coverage: From ESD, TVS, TSS, PPTC to common-mode chokes and Schottky diodes, Leiditech provides the complete set of protection components required for domain control platforms.

· Verifiable solutions: Leiditech has an in-house EMC laboratory, offering customers testing support for ESD, surge, EFT, automotive load dump ISO 7637 5a/5b, and more, shortening the certification cycle.

· Local support: Shanghai headquarters + FAE team, providing device selection and optimization for specific PCB layouts, harness lengths, and target test levels.

 

Shanghai Leiditech translates the EMC risks of key interfaces — including automotive Ethernet, CAN FD, LIN, automotive power supplies, BMS daisy chains, GNSS/RF, radar/camera — into clear circuit topologies and verified automotive-grade part numbers. If you are developing a domain control platform based on the NX9031C or similar high-compute autonomous driving chips, feel free to contact the Leiditech EMC engineer for protection solutions, reference circuits, and sample support tailored to your specific interface topology.

Laisser un commentaire

Votre adresse e-mail ne sera pas publiée. Les champs obligatoires sont indiqués. *
Nom
Email
Contenu
Code de vérification
ver_code