Installed a TVS but the port still burned out? The problem lies in the selection! Leiditech snap-back low clamping voltage protection solution
Hardware and EMC engineers have most likely encountered this pitfall: even with ESD protection devices added to circuit ports, downstream chips still get damaged during ESD and surge testing, leading to doubled repair and redesign costs.
In Spectrum Analyzer Repair and Limiter Design, senior EMC expert Mr. Song from Xiaomi documented a typical failure case: an entry-level spectrum analyzer suffered damage to its RF switch and digital attenuator due to transient high-voltage surges caused by power grid switching. The issue was resolved using Leiditech's snap-back ESD device, the LM112501.
This article, drawing on Mr. Song's practical repair experience, starts from first principles to analyze an innovative device technology for transient protection — Leiditech's snap-back ESD/TVS devices.
II.Fatal shortcomings of conventional ESD/TVS devices
After a conventional ESD/TVS device breaks down and conducts, the clamping voltage rises proportionally with the increasing surge current.
From the I-V curve, we can clearly see that for a conventional ESD/TVS device, once the port voltage exceeds the device's breakdown voltage, the device conducts. As the surge current continues to increase, the clamping residual voltage rises proportionally. The higher the pulse energy, the larger the residual voltage value, and the poorer the protection for the downstream IC becomes.
II.Snap-back protection devices: true low clamping voltage protection
The snap-back ESD/TVS internally uses an SCR (silicon-controlled rectifier) structure. After triggering, its internal resistance drops sharply, exhibiting negative resistance snap-back characteristics:
After triggering and conduction, the voltage drops rapidly, maintaining an extremely low clamping voltage even under high current, providing excellent protection for low-voltage-tolerant chips.
Intuitive parameter comparison (5V signal version):
|
Type |
Part Number |
|
VBR(V) |
VCmax@A |
C(PF) |
Package |
|
Snap-back type |
ULC0521CLV |
5 |
5.8 |
8V@6A |
0.3 |
DFN0603 |
|
ULC0542CLV |
5 |
5.8 |
8V@6A |
0.3 |
DFN1006 |
|
|
Conventional type |
ULC0521C |
5 |
6.5 |
25V@5A |
0.3 |
DFN0603 |
|
ULC0542C |
5 |
6.5 |
25V@4A |
0.3 |
DFN1006 |
Under the same current, the clamping voltage Vc of a conventional device is more than three times that of a snap-back type, significantly reducing the protection effectiveness for the chip.
III.Specialized snap-back device solutions for mainstream scenarios
3.1 3.3V RF / Precision Instrument Ports
Leiditech's solution meets the ESD protection requirements for RF interfaces. The LM112501 features ultra-low capacitance to ensure signal integrity, with contact discharge of ±30kV and air discharge of ±30kV. If IEC 61000-4-5 surge testing is required, a GDT device should be placed at the front end.
Ÿ Operating voltage 3.3V, with extremely low leakage current that does not interfere with weak RF signals.
Ÿ Junction capacitance of only 1.5pF, ensuring no loss at high frequencies.
Ÿ Clamping voltage controlled within 8V under 25A high-current surges, effectively protecting downstream devices.
3.2 Type-C Fast Charging CC/SBU Signal Dedicated: ULC2442CS, ULC2421CS
The operating voltage of USB Type-C fast charging interfaces is typically 24V. Adjacent CC and SBU signal lines are highly susceptible to coupling 24V high voltage. Using a 5V general-purpose ESD would cause frequent false triggering and breakdown; while conventional 24V ESD has excessively high clamping voltage, still damaging downstream low-voltage-tolerant chips. For this scenario, Leiditech recommends two bidirectional snap-back ESD devices, with parameters as follows:
|
Parameters |
ULC2442CS |
ULC2421CS |
|
Rated reverse working voltage VRWM |
24V |
24V |
|
Breakdown snap-back characteristic |
30V snap-back to 2.9V |
30V snap-back to 2.9V |
|
Package specification |
DFN1006-2 |
DFN0603-2 |
|
Maximum peak pulse current IPP |
5A |
5A |
|
Vc (8/20μs - 1A) |
4.0V |
4.0V |
|
Vc (8/20μs - 5A) |
6.0V |
6.0V |
|
Dynamic on-resistance RDYN (L-GND) |
0.320 |
0.320 |
|
Pulse clamping voltage Vc (TLP-16A) |
8.2V |
8.2V |
|
Zero-bias junction capacitance CJ (0V, 1MHz) |
0.5-0.7 pF |
0.5-0.7 pF |
This series features junction capacitance as low as 0.5pF and a clamping voltage of only 4V under 1A pulse, resolving the protection conflict between 24V coupled high voltage and downstream low-voltage chips. It is particularly suitable for various Type-C fast charging data cables (not for use on power paths).
3.3 High-Power Snap-Back TVS for Power Supply Circuits
Leiditech's 6LM/3LM/5LM series high-power TVS models feature large peak pulse current capability, reducing the voltage rating requirements for downstream DC-DC components and lowering BOM costs. They are suitable for surge protection in industrial and automotive power supplies. They meet the wide-voltage input requirements of industrial and automotive 24V power supplies within 32V, and comply with IEC 61000-4-5 Level 4, line-to-ground ±4kV . They also meet IEC 61000-4-2 Level 4 standards (achieving ±30kV contact/air discharge). An anti-reverse connection function can be implemented by pairing with a Schottky diode such as the SS56LF .
IV.These scenarios prioritize the use of snap-back ESD/TVS:
Although this article starts from a spectrum analyzer repair failure, snap-back protection devices are applicable to all low-voltage, high-precision circuits. The core application areas are as follows:
1. High-end RF test equipment: RF input ports of network analyzers, signal receivers, and vector instruments.
2. Medical electronic equipment: Weak signal acquisition front-ends such as ECG and endoscopes.
3. Industrial control communication: RS485 and CAN bus, resistant to surges and ESD in harsh factory conditions.
4. High-end consumer electronics: USB 3.0 and Type-C high-speed data cables.
5. Automotive electronic systems: Various sensor communication interfaces and low-voltage signal interfaces.
|
Leiditech snap-back TVS part number table for power supply applications, effectively reducing downstream DC-DC cost |
||||||
|
Model |
PPP (W) |
VRWM (V) |
Vbr min (V) |
Vc max(V) |
IPP(A) |
Package |
|
LM10S26CAT |
11000 |
26 |
28.9 |
27 |
- |
DO-218AB |
|
LM10S28CAT |
11000 |
28 |
31.1 |
29 |
- |
DO-218AB |
|
LM10S33CAT |
11000 |
33 |
36.7 |
32 |
- |
DO-218AB |
|
LMBJ58CP5 |
3500 |
58 |
64.4 |
51 |
70 |
SMB |
|
LMBJ58CP4 |
3000 |
58 |
64.4 |
60 |
50 |
SMB |
|
3LM26CA |
3000 |
26 |
28.9 |
28.1 |
152.2 |
SMC |
|
3LM33CA |
3000 |
33 |
36.7 |
38 |
101.8 |
SMC |
|
5LM26CA |
5000 |
26 |
28.9 |
30.3 |
202.8 |
SMC |
|
5LM33CA |
5000 |
33 |
36.7 |
38 |
151.2 |
SMC |
|
6LM26CA |
600 |
26 |
28.9 |
24.5 |
33.7 |
SMB |
|
6LM33CA |
600 |
33 |
36.7 |
30.1 |
26.32 |
SMB |
|
Leiditech Snap-back ESD Part Number Table (Continuously Updated) |
||||||
|
Part Number |
Vrwm(V) |
Vbr |
VCmax@A |
C(PF) |
Package |
Applications |
|
ULC0321CDNH |
3.3 |
8 |
8V@5A |
0.5 |
DFN0603 |
3.3V High-Speed Signal |
|
ULC0321S |
3.3 |
6.3 |
15V@5A |
0.2 |
DFN0603 |
|
|
ULC0322P10LV |
3.3 |
3.5 |
5V@10A |
0.6 |
DFN0603 |
|
|
ULC0342CDNH |
3.3 |
4 |
5.5V@6A |
0.22 |
DFN1006 |
|
|
ULC0342P |
3.3 |
3.5 |
5V@10A |
0.6 |
DFN1006 |
|
|
LM112501 |
3.3 |
3.5 |
8V@16A |
1.5 |
SOD323 |
|
|
ESD0321CW |
3.3 |
3.7 |
8V@21A |
30 |
DFN0603 |
3.3V general-purpose I/O |
|
ULC1811CDNH |
18 |
22 |
6V@5A |
0.5 |
DFN1006 |
18V, 24V signals such as Type-C CC/SBU |
|
ULC2421CS |
24 |
30 |
6V@5A |
0.5 |
DFN0603 |
|
|
ULC2421CDNH |
24 |
26 |
7V@6A |
0.48 |
DFN0603 |
|
|
ULC2442CS |
24 |
30 |
6V@5A |
0.5 |
DFN1006 |
|
|
ESDA05CP30 |
5 |
6 |
7.2V@8A |
15 |
DFN1006 |
5V general-purpose I/O
5V high-speed signal |
|
ESDA05CPX |
5 |
6 |
8.5V@18A |
25 |
DFN1006 |
|
|
ESDA05CP |
5 |
6 |
10V@8A |
15 |
DFN1006 |
|
|
ULC0542CDNH |
5 |
8 |
6V@5A |
0.5 |
DFN1006 |
5V power ESD protection |
|
ULC0511CDNH |
5 |
6 |
7V@9A |
0.3 |
DFN1006 |
|
|
PTVS0542H100 |
5 |
6.3 |
9V@100A |
200 |
DFN1006 |
4.5V power ESD protection 5V general-purpose I/O |
|
USSD0571P6W |
|
6 |
11V@110A |
350 |
DFN1610 |
|
|
SMDA05N |
5 |
5.5 |
9V@50A |
110 |
DFN1006 |
|
|
SMDA45N |
4.5 |
5.0 |
8.8V@80A |
200 |
DFN1006 |
|
V.summary
When selecting protection components, don't just look at power ratings. Low clamping voltage Vc and high peak pulse current Ipp are the core metrics.
Conventional ESD/TVS devices have excessively high residual voltage under high current, making precision high-speed circuits and fast-charging interfaces highly susceptible to chip damage.
Leiditech snap-back ESD/TVS combines three key advantages: low residual voltage, low capacitance, and high surge discharge current, enabling one-step ESD and surge rectification.
Leiditech offers a full range of EMC components including TVS, ESD, TSS, etc., backed by free laboratory testing and professional EMC rectification services to solve port ESD burnout issues across all applications.
Laisser un commentaire
- PoE power supply methods and EMC protection in the DC power supply system of intelligent logistics robots
- EMC protection design for access control security devices: the four external interfaces that deserve the most attention
- From power to antenna: EMC protection design solution for video doorbells
- Solving lightning and ESD hazards in industrial sites: LVDT pressure transmitter protection design
- Micro PLC crashes, resets, and communication packet loss? EMC is the root cause.
